8000系列模块化高压电源

型号：8000系列高压电源模块

功率：20W 50W 80W 100W 120W

输入电压：85V AC -265V AC

输出电压：1kV 2kV 5kV 10kV 15kV 20kV 30kV 40kV 50kV

下载说明文档 (PDF File)

产品详细介绍

Genvolt 8000系列是一款坚固耐用的模块化系列直流高电压供应范围, 电源输入电压从85V AC- 265V AC 50/60Hz。输出功率从1 kv - 70 kv选项。

Genvolt 8000系列具有主动升压型功率因数校正前端——即有源整流器。在主电源频率下提供非常低的谐波失真，功率因数高达0.99。

　
Genvolt 8000系列模块化高压电源具有唯一的固定极性，（正极性或负极性）。采购是需确定电源极性。

Genvolt 8000系列高压电源模块具有恒压员工作模式和恒流源工作模式两种工作模式，并且可以快速切换两种工作模式。

Genvolt 8000系列模块化高压电源具有输出短路保护或电弧保护，,温度保护和过压保护，能够在苛刻的环境中使用。

The Genvolt 8000 series is a rugged modularised range of AC-input DC High Voltage supplies, designed to operate from a universal mains input from 85VAC to 256VAC 50/60Hz. Power Output options from 1kv to 70kV.

They feature an active boost-style Power Factor Correction front end – i.e. an active rectifier. This offers a very low harmonic distortion at mains frequencies with a power factor of up to 0.99.

The modules have a FIXED polarity output which should be specified at the time ordering using the “Model Finder” table.

They operate in both Voltage Control and Current Control modes with fast active crossover between the modes.

Protection against output short circuits or arcs, over temperature and output overvoltage allow for operation in demanding environments.

Input Specification

AC Input voltage range	85VAC to 256VAC, 47 – 63 Hz
Power Factor	FL 0.99 NL 0.98
Output Polarity	+ve or –ve (Please specify when ordering)
Voltage Load Regulation	0.01% of full voltage for a no load to a full load change
Voltage Line Regulation	+/- 0.005% of full voltage over the specified input voltage range
Current Load Regulation	0.01% from 0V to full voltage
Current Line Regulation	+/- 0.01% of full current over the specified input voltage range per 8 hours after
Voltage Ripple:	0.1% p-p of output voltage
Current Stability	0.02% per 8hrs after ½hr warm up
Temperature Coefficient	100 ppm per oC
Temperature	Operating 0^oC to 45^oC Storage -20^oC to +85^oC
Interlock	Open Interlock will shut down unit
Circuit Protection	Overvoltage, Overcurrent, Arcing and Over temperature
Relative Humidity	Non condensing

The control signal is NOT a safety interlock and must NOT be used for a protection system from high voltage generation for safety purposes.

Standard Features, as fitted at the factory

Control	Logic level for high voltage enable/disable.
Overvoltage Protection	Overvoltage conditions can be caused by excessive input program signal. If an overvoltage condition is detected, the power supply is latched off until input power is reset.
PS Fault Condition	A PS fault indicator and a PS fault output on J1, indicate an OVP or a regulation error.
PF and Universal Input	The input voltage of the 8000 can operate within the range from 85VAC to 265VAC. The power factor is actively corrected across the entire range and is better than 0.99 at full load.
Internal EMI Filter	An internal EMI filter and fuse provide protection against line voltage surges and power supply faults

Remote Operating Features

Remote Programming	Allows remote adjustment of the output voltage and current, via an external voltage source.
Remote Monitor	Allows remote monitoring of the output voltage and current.
High Voltage Enable/Disable	Allows remote ON/OFF control of the high voltage.
+10VDC Reference	A +10VDC is provided for remote programming via a potentiometer or voltage divider.

Mechanical Details

Weight	Model specific, approximately 3Kgs
Dimensions	95.25mm (H) x 127mm (W) x 279.4mm (D)
Power Input Connector	IEC320 with mating connector x 2 Metres
HV Output Connector	Proprietary HV Connector
Control Interface Connector	15 pin ‘D’ connector (Male)

Regulatory Approvals

Compliant to 2004/108/EC, the EMC directive
2006/95/EC, the low voltage directive
RoHS compliant and CE approved

Maximum Voltage	Maximum Current	Polarity	Model Number
1kV	120mA	P or N	80120P (+ve) or 80120N (-ve)
5kV	24mA	P or N	8024P (+ve) or 8024N (-ve)
10kV	12mA	P or N	8012P (+ve) or 8012N (-ve)
20kV	6mA	P or N	806P (+ve) or 806N (-ve)
30kV	4mA	P or N	804P (+ve) or 804N (-ve)
40kV	3mA	P or N	803P (+ve) or 803N (-ve)
50kV	2.4mA	P or N	8050P (+ve) or 8050N (-ve)
60kV	2mA	P or N	8060P (+ve or 8060N (-ve)
70kV	1.7ma	P or N	8070P (+ve) or 8070N (-ve)

Typical applications include:

Electrospinning & Electrospraying
X-ray Generation
Insulation Testing
Capacitor Charging (contact Genvolt for individual applications)
Laboratory Use